Light commercial
Showing 100–198 of 694 results
Pads
Support plate, rubber pad, rectangular | for TESLA vehicles | 1 set / 4 pieces
Stands for alignment
1 set / 4 pieces
Vehicles lift platforms
Ramp height 60 mm, for extremely low vehicles | 1 set / 2 pieces
Tool support
Ergonomic holder for impact wrench
Gearbox-plates GA III
Adjustment angle: ± 40° / ±17°, tensioning belt to secure the load, measurements adjustable to 600 x 400 mm, capacity 1 t, peg Ø 35 mm, measurements 400×300 mm
Gearbox-plates GA IV
Adjustment angle= ± 12°, weight = 23 kg, large rubber supporting surface, tensioning belts to secure the load, comfortable tilting in all directions by fork spanner, extremely flat construction, in series galvanised, capacity 1 t, peg Ø 35 mm, measurements 530x380x120 mm
Prismatic blocks
For GA IV | 2 pieces
Pads
Support plate | for Mercedes G-Class – front and rear | 1 set / 4 pieces
Pads
Support plate, U-support | 1 set / 4 pieces
Pads
Support plate, centering mushroom | for Fiat 500E, 500 ABARTH | 2-stage | 1 set / 4 pieces
Supporting bridge GSV
Adjustable 900 – 1180 mm, capacity 15 t, with Rollerset
Tool trays
Magnetic | 1 set / 2 pieces
Pads
Prism, mandrel | for Mercedes Sprinter, VW Crafter | 1 set / 6 pieces
-
Supporting bridge SPZ-15
Pads
Support plate | for VW MEB platform E-vehicles | 1 set / 4 piece
Pads
Mandrel | for Fiat Ducato, Peugeot Boxer, Citroën Jumper – front and rear | 1 set / 4 pieces
Adjustable drive
Additional adjustable drive to mobilise the fixed lifting unit, incl. extended hanging control pad, reversing device, chain and cover
Automatic ”run-into” protection
Light barrier max.15 m
Automatic ”run-into” protection
Position indicator for craneway
Automatic ”run-into” protection
Mount for automatic ”run-into” protection according to requirements
Automatic axle distance preselection
AAV-Control
Cable suspension
Balancer to disconnect hand-held control panel
Cable suspension
Mount for running rail according to requirements
Temporary cover
Wooden slats to insert in frame, capacity: max. 100 kg/m², per meter
Trolley SmartCart
for DUPLEX load-carrying equipment, incl. 4 swiveling rollers
Aggregate assembly device V00-2
for Vito with V6 petrol engine)
Universal support Ø 35 mm
Mounting hole Ø 35 mm, suitable for holding various tools, such as the transmission plate GA passenger car | fitted with a bushing
Stand for the control cabine | 600 mm
1 piece
Cassette extended (primary coated)
Incl. FLEXCOVER, per meter
Cassette galvanized
Instead of primary coat, per meter
Frame extended (primary copated)
Incl. FLEXCOVER, per meter
Frame galvanized
Instead of primary coat, per meter
Frame with overhang
Frame incl. FLEXCOVER, each piece
Frame with overhang
Frame, galvanised execution, incl. FLEXCOVER, each piece
Pump sump
for lift cassette
Floor stand
800 mm wide (for T/L-4 platform)
Floor stand
1000 mm wide (for T/L-5 platform)
Twin control
(2 lifts, synchronized or individually controllable)
Vehicle fuses
For turntable, Ø 120 mm | 1 set / 4 pieces
Adaption for CDI-Motor V00-1
Weight: 5 kg, capacity: 250 kg
Support plate X
20 t, 55 mm peg diameter
Traverse ATEB S2
7.5 – 15 t, 55 mm peg diameter
Front and rear adapters HydroLift
For lifting various tractors, incl. various receiving means – agricultural receiving means for HydroLift, load capacity 16.4 t
Condensate drain/filter combination
Pads
Support plate, rubber support, round | R, 15 t, Ø 55 mm
Support trestle
7500 kg, 1330 – 2030 mm
Spacer DS 1
Height 100 mm, capacity 15 t
Spacer DS 2
Height 200 mm, capacity 15 t
Spacer DS 3
15 t, 35 mm peg diameter
Support plate H
15 t, 35 mm peg diameter
Support plate P
15 t, 35 mm peg diameter
Support plate P MAN
15 t, 35 mm peg diameter
Support plate R
15 t, 35 mm peg diameter
Support plate U
15 t, 35 mm peg diameter
Support plate U
15 t, 55 mm peg diameter
Support plate U 145
15 t, 35 mm peg diameter
Support plate U 175
15 t, 35 mm peg diameter
Support plate U 220
15 t, 35 mm peg diameter
Support plate X
15 t, 35 mm peg diameter
Supporting bridge DB
Wooden blocks 100 x 200 x 360 mm, capacity 15 t
Traverse ATB
15 t, 55 mm peg diameter, standard traverse for buses
Traverse ATS
15 t, 55 mm peg diameter
LED lighting kit for Exa Lift HDVL | 6-way
8 / 9 / 10 m
Diagnostic kit STDADIAG/SW
TEXA IDC5 SW KIT – Diagnostic setup for those who already have TEXA devices (e.g., ADAS RCSS)
Traverse ATEB S2
7.5 – 15 t, 45 mm peg diameter
Traverse ATS
20 t, 55 mm peg diameter
Oil-water separator Öwamat 10
For compressor capacities up to 58.5 m³/min
Protection cover HydroLift
Splash water protection for HydroLift
Spacer DR 4
Height 400 mm, capacity 30 t
Spacer DR 5
Height 500 mm, capacity 15-30 t
Spacer DR 5
Height 500 mm, capacity 10 t
Spacer DR 6
Height 600 mm, capacity 30 t
Support platform 15 t, mobile
Transportable support platform lowered under load, for use in conjunction with U-brackets, primed and lacquered
Supporting bridge GS
Universal, capacity 15 t, with Rollerset
Supporting bridge GSB
Extra flat, capacity 15 t, with Rollerset
Supporting bridge GSB Vario
Extra flat, capacity 15 t, with Rollerset
Supporting Package I
15 t, 55 mm peg diameter, navigable
Supporting Package II
15.5 t, 55 mm peg diameter, navigable
Supporting Package IV
15 t, 55 mm peg diameter, navigable
Traverse ATB MAN TGA-Set
15 t, 55 mm peg diameter
Traverse ATB Truck-Set
15 t, 55 mm peg diameter
Traverse ATK
15 t, 55 mm peg diameter
Diagnostic kit STDADIAG
IDC5 KIT TEXA – for diagnostic wheel alignment | kit for those who have a wheel alignment but no TEXA accessories
Supporting Package III
15 t, 55 mm peg diameter, navigable
Support trestle
10000 kg, 1235 – 2040 mm
Eyebolt
3.5 t – 4.2 t | facilitates installation of the lift, can be used again for other installations | 1 set
Inground cable connection kit
Allows columns connection cables to be placed inground | 1 piece
Crossbar height adjustment
Kit for increasing overhead cable passage height by up to +1.5 m | for spindle lifts | 1 set
Mounting set for traverse ATT 3,2 C | for cars / vans / MAN / Crafter / Sprinter
optional accessories for the transporter receptacle, recommended plug-in pick-up set
Spacer DS 1
Height 100 mm, capacity 30 t
Spacer DS 2
30 t, 80 mm peg diameter
Spacer DS 3
Height 250 mm, capacity 30 t
Supporting bridge VS
Connecting set, capacity 30 t
Traverse ATS
20 t, 80 mm peg diameter
Wheel clamps Fast clamps
Quick-clamps | for CCD wheel aligners, passenger car, tyre size 21 – 31″, wheel Ø 540 – 780 mm, max. wheel weight 3.8 kg | 1 set / 2 pieces
Spacer DS 2
Height 150 mm, capacity 30 t
Spacer DS 3
30 t, 55 mm peg diameter
Support plate H
20 t, 55 mm peg diameter
Support plate H
20 t, 80 mm peg diameter