Accessories lifts
Accessories for workshop lifts can seriously make a difference. Our selection of accessories lifts includes kits, rubber pads, covers and much more.
Showing 199–297 of 657 results
Run-up ramps
3300 mm | for all surface installation versions | 1 pair
Run-up ramps
2300 mm | 1 pair
Run-up ramps
Long, 2300 mm | ramps S8000A10 replacing the standard ramps | 1 pair
Segment Pit Covering
for monolithic constructed pits, per meter
Spacer DR 4
Height 400 mm, capacity 10 trnSpacer tubes to compensate for particularly large height differences between support bridges and load, with fall-through protection as standard, per piece
Spacer DR 4
Spacer DR 6
Height 600 mm, capacity 10 t
Spacer supports bushing Ø 60 mm
1 set / 2 pieces
Spacers 10 mm | for K arms | 1 set / 4 pieces
Spacers 140 mm
For Fiat Ducato, Peugeot Boxer and Citroën Jumper | for quick drop-in of the K arms, Ø 45 mm | 1 set / 4 pieces
Spacers 140 mm | or quick drop-in of the R arms
Set of pad extensions for 2-post lifts | 1 set / 4 pieces
Spacers 200 mm
For Fiat Ducato, Peugeot Boxer and Citroën Jumper | bushing Ø 45 mm | 1 set / 4 pieces
Spacers 200 mm, bushing Ø 60 mm | 1 set / 4 pieces
200 mm, bushing Ø 60 mm | 1 set / 4 pieces
Spacers 80 mm
For Fiat Ducato, Peugeot Boxer and Citroën Jumper | for quick drop-in of the K arms, Ø 45 mm | 1 set / 4 pieces
Spacers for 4-post lifts
To close turntable housing (As a replacement for turntables) | 1 set / 2 pieces
Spacers for 4-post lifts
To close turntable housing (As a replacement for turntables) | 1 set / 2 pieces
Spacers for 4-post lifts
To close turntable housing (As a replacement for turntables) | 1 set / 2 pieces
Spacers for 4-post lifts
To close turntable housing (As a replacement for turntables) | 1 set / 2 pieces
Spacers for wheel alignment versions of series 6352
To total close turntable housing | 1 set / 10 pieces
Spacers for wheel alignment versions of series 6352
To close turntable housing | 1 set / 6 pieces
Special pads increased, 90 mm | for M30 thread arms | 1 set / 4 pieces
For vehicles with internal lifting points (for example for: Renault Espace and Talisman)
Special pads increased, 90 mm | for M30 thread arms | 1 set / 4 pieces | Supplied in place of the standard pads
For vehicles with internal lifting points (for example for: Renault Espace and Talisman)
Support Kit
2 pieces, for Sprinter/Crafter, back
Support Kit VAS 6355A/2
2 pieces, for Sprinter/Crafter
Support pads for Fiat 500E, 500 ABARTH
Supports for 2-post lifts | 1 set / 4 pieces
Support pads for Mercedes Sprinter/VW LT + Crafter | Ø 45 mm
V-shaped supports | bushing Ø 45 mm | 1 set / 2 pieces
Support pads for Mercedes Sprinter/VW LT + Crafter | Ø 45 mm
Holding set, adjustable – 2 x rod-shaped supports, 2 x V-shaped supports | bushing Ø 45 mm | needed spacers S224A3-A4 S370A18 | 1 set / 4 pieces
Support pads for Mercedes Sprinter/VW LT + Crafter | Ø 60 mm
V-shaped supports | bushing Ø 60 mm | 1 set / 2 pieces
Support pads TESLA | for EV arms
Supports for 2-post lifts | 1 set / 4 pieces
Support pads TESLA | for K arms Ø 45
Supports for 2-post lifts | 1 set / 4 pieces
Support pads TESLA | for K arms Ø 55
Supports for 2-post lifts | 1 set / 4 pieces
Support trestle
10000 kg, 1235 – 2040 mm | with on springs retracting rollers
Supporting arm extensions
Capacity reduced to 3.5 t | 1 set / 2 pieces
Supporting arm extensions
90 mm, capacity reduced to 2.7 t | 1 set / 2 piec
Supporting arm extensions
Capacity reduced to 3.7 t | for LIK arms | 1 set / 2 pieces
Supports for chassis lifting | adjustable | bushing Ø 45 mm | 1 set / 4 pieces
Needed spacers S224A3-A4, S370A18
Supports for chassis lifting | adjustable | bushing Ø 60 mm | 1 set / 4 pieces
Needed spacers S370A7-A8-A15
Supports for spacers, bushing Ø 45 mm
For 2-post lifts | 1 set / 2 pieces
Surcharge for rail chassis with lateral flanged rollers (set consisting of 4 pieces)
Tool trays | magnetic | 1 set / 4 pieces
Towing lever Capacity 3000 / 4000 / 5500 kg
Turntable covers for 615 mm platforms
Spacers to completely close turntable recess | suitable for RAV.640N2.193117, RAV.640N2.193469, RAV.640N2.193001, RAV.640N2.193582, RAV.640N2.193216, RAV.640N3.192981 and RAV.640N2.193476 | 1 set / 2 pieces
U-support
Vehicles lift platforms 1 set / 4 pieces
Ramps for extra low clearance vehicles
Wheel alignment stands | load capacity per stand 800 kg
Accessory for wheel aligner | 1 set / 4 pieces
Wheel fork extension 150 mm
Extensions for adjustable fork (1 per column) | 1 set
Wheel fork reduction
For wheels Ø 500 – 700 mm | 1 piece
Wheel fork reduction
For wheels Ø 800 – 900 | 1 piece
Wheel free cross beam for U-versions | capacity 15000 kg
Wheel free cross beam for U-versions | Capacity 20000 kg
Wheel free cross-beam max. 20000 kg
Crossbar for standard lifts with adjustable fork
Wheel-lifting platform kit
Width extendion 200 mm
Width extendion 200 mm
200 mm
Width extension
For 2-post lift KPX35LLE | enables columns to be widened up to 3200 mm
Rubber pads
160 x 120 x 80 mm | 1 set / 4 pieces
Rubber pads
160 x 120 x 40 mm | 1 set / 4 pieces
Spacers for pads
4 x 89 mm, 4 x 127 mm, incl. 2 brackets for mounting on the pillars | for SPOA3T | 1 set / 8 pieces
Spacers for pads
4 x 200 mm, incl. bracket for mounting on the pillars | 1 set / 4 pieces
Pads
Support plate, rubber pad, rectangular | for TESLA vehicles | 1 set / 4 pieces
Stands for alignment
1 set / 4 pieces
Vehicles lift platforms
Ramp height 60 mm, for extremely low vehicles | 1 set / 2 pieces
Pads
Support plate, rubber support, round | Ø 80 mm | 1 set / 4 pieces
Tool support
Ergonomic holder for impact wrench
Gearbox-plates GA III
Adjustment angle: ± 40° / ±17°, tensioning belt to secure the load, measurements adjustable to 600 x 400 mm, capacity 1 t, peg Ø 35 mm, measurements 400×300 mm
Gearbox-plates GA IV
Adjustment angle= ± 12°, weight = 23 kg, large rubber supporting surface, tensioning belts to secure the load, comfortable tilting in all directions by fork spanner, extremely flat construction, in series galvanised, capacity 1 t, peg Ø 35 mm, measurements 530x380x120 mm
Prismatic blocks
For GA IV | 2 pieces
Pads
Support plate | for Mercedes G-Class – front and rear | 1 set / 4 pieces
Pads
Support plate, U-support | 1 set / 4 pieces
Axial traverse ATEB S2 TWIN
7.5 – 15 t, 55 mm peg diameter
Extension of the pit crossing SPZ-15
Pit crossing as retrofit set
Pads
Support plate, centering mushroom | for Fiat 500E, 500 ABARTH | 2-stage | 1 set / 4 pieces
Supporting bridge GSV
Adjustable 900 – 1180 mm, capacity 15 t, with Rollerset
Jacking Beam 2,6 t
Capacity 2600 kg
Pads
Mandrel | for Mercedes Sprinter, VW Crafter – front / for SPO54 | 1 set / 2 pieces
Parking position switch rolling jack
For scissor lift S38/S50 | retrofit kit
Tool trays
Magnetic | 1 set / 2 pieces
Pads
Prism, mandrel | for Mercedes Sprinter, VW Crafter | 1 set / 6 pieces
Supporting bridge SPZ-15
Pads
Support plate | for VW MEB platform E-vehicles | 1 set / 4 piece
Pads
Mandrel | for Fiat Ducato, Peugeot Boxer, Citroën Jumper – front and rear | 1 set / 4 pieces
Pads
Prism | for Mercedes Sprinter, VW Crafter – rear / for SPO54/55 | 1 set / 2 pieces
Rubber pad
Round | Ø 123 mm | for pad FJ6202 | 1 piece
Washing Bay Kit HDVL
Twin control
(2 lifts, synchronized or individually controllable)
Vehicle fuses
For turntable, Ø 120 mm | 1 set / 4 pieces
Drive-on ramps 2510 mm
Floor installation kit for lifts | 1 set / 2 pieces
Drive-on ramps 3300 mm
Floor installation kit for lifts | 1 set / 2 pieces
Retrofit kit Air supply
For jacking beam
SmartCart Agrar
for tractor adapter set HydroLift
Support plate X
20 t, 55 mm peg diameter
Traverse ATEB S2
7.5 – 15 t, 55 mm peg diameter
Ramp set
Drive-on ramp kit for forklift trucks, accessible from one side | for HydroLift 6,2 / 7,5 / 8,2 | Grey (RAL 7012)
Ramp set
Drive-on ramp kit for forklift trucks, accessible from both sides | for HydroLift 6,2 / 7,5 / 8,2 | Grey (RAL 7012)
Ramp set
Drive-on ramp kit for three-wheel forklift, accessible from one side | for HydroLift 6,2 / 7,5 / 8,2 | Grey (RAL 7012)
Transport trolley for ramp set for HydroLift 6,2 / 7,5 / 8,2
Trolley for drive-on kit for forklift trucks
Floor leveling FloCo | incl. kit for S-CAT-Lift
Front and rear adapters HydroLift
For lifting various tractors, incl. various receiving means – agricultural receiving means for HydroLift, load capacity 16.4 t
Wheel fork extension
Ideal for lifting motorhomes where the wheels are mounted behind the coachwork | for Hydrolift 6,2 / 7,5 | Grey (RAL 7016)