Accessories lifts
Accessories for workshop lifts can seriously make a difference. Our selection of accessories lifts includes kits, rubber pads, covers and much more.
Showing 100–198 of 482 results
Power unit passenger side | 13.12 ft
Power unit passenger side | 16.40 ft
Power unit passenger side | 6.56 ft
Power unit passenger side | 9.84 ft
Ramp extension
Optional for wheel alignment | for SM40/55/LT/65
Receptacle for semitrailer on kingpin
Remote control for Duplex T2 / T3 control unit C2 / C3 / C4 (Classic / Plus / Premium)
The system can be operated flexibly by remote control without being tied to a specific location
Rest position switch
1 piece – 2 pieces must be ordered | When the traverses are in the lowest positions, the green signal lamp on the control cabinet lights up
Rubber pads
120 mm | suitable for RAV.640N1.193391, RAV.650N1.193742, RAV.650N2.193858, RAV.650N2.193520, RAV.650N2.193667, RAV.650N6.193964, RAV.650N5.193902, RAV.660N2.193360, RAV.650N5.193018, RAV.650N6.193025, RAV.640N5.193049, RAV.640N4.192998, RAV.640N3.192981, RAV.650N2.193384 and RAV.650N5.193919 | 1 set / 4 pieces
Rubber pads
20 mm | suitable for RAV.640N1.193391, RAV.650N1.193742, RAV.650N2.193858, RAV.650N2.193520, RAV.650N2.193667, RAV.650N6.193964, RAV.650N5.193902, RAV.660N2.193360, RAV.650N5.193018, RAV.650N6.193025, RAV.640N5.193049, RAV.640N4.192998, RAV.640N3.192981, RAV.650N2.193384 and RAV.650N5.193919 | 1 set / 4 pieces
Rubber pads
200 mm | suitable for RAV.640N1.193391, RAV.650N1.193742, RAV.650N2.193858, RAV.650N2.193520, RAV.650N2.193667, RAV.650N6.193964, RAV.650N5.193902, RAV.660N2.193360, RAV.650N5.193018, RAV.650N6.193025, RAV.640N5.193049, RAV.640N4.192998, RAV.640N3.192981, RAV.650N2.193384 and RAV.650N5.193919 | 1 set / 4 pieces
Rubber pads
40 mm | suitable for RAV.640N1.193391, RAV.650N1.193742, RAV.650N2.193858, RAV.650N2.193520, RAV.650N2.193667, RAV.650N6.193964, RAV.650N5.193902, RAV.660N2.193360, RAV.650N5.193018, RAV.650N6.193025, RAV.640N5.193049, RAV.640N4.192998, RAV.640N3.192981, RAV.650N2.193384 and RAV.650N5.193919 | 1 set / 4 pieces
Rubber pads
60 mm | suitable for RAV.640N1.193391, RAV.650N1.193742, RAV.650N6.193964, RAV.660N2.193360, RAV.650N6.193025, RAV.640N5.193049 and RAV.640N4.192998 | 1 set / 4 pieces
Segment Pit Covering
for monolithic constructed pits, per meter
Spacers for 4-post lifts
To close turntable housing (As a replacement for turntables) | 1 set / 2 pieces
Spacers for 4-post lifts
To close turntable housing (As a replacement for turntables) | 1 set / 2 pieces
Stand for the control cabine | 600 mm
1 piece
Support set for wheel free
Surcharge for rail chassis with lateral flanged rollers (set consisting of 4 pieces)
Tension belt gauge
Towing lever Capacity 3000 / 4000 / 5500 kg
Transport trolley SmartCart XS | for Duplex load-carrying equipment
The convenient workshop helper with 33 slots – the attachments find their place in a tidy manner
Wheel fork extension 150 mm
Extensions for adjustable fork (1 per column) | 1 set
Wheel-lifting platform kit
Rubber pads
160 x 120 x 80 mm | 1 set / 4 pieces
Rubber pads
160 x 120 x 40 mm | 1 set / 4 pieces
Pads frame adapters kit
Pads frame adapters kit Ø 120 mm (1 set, 2 pcs), for turntable
Spacers for pads
4 x 200 mm, incl. bracket for mounting on the pillars | 1 set / 4 pieces
Pads
Support plate, rubber pad, round | Ø 80 mm | 1 set / 4 pieces
Pads
Support plate, rubber pad, rectangular | for Tesla | 1 set / 4 pieces
Mounting set for traverse ATT 3,2 C
Optional accessories for the transporter receptacle, recommended plug-in pick-up set | for cars / vans / MAN / Crafter / Sprinter
Stands for alignment
1 set / 4 pieces
Vehicles lift platforms
Ramp height 60 mm, for extremely low vehicles | 1 set / 2 pieces
Gearbox plate GA passenger car
Adjustment angle +/- 10°, load capacity 400 kg, peg Ø 35 mm, measurements 300 x 240 mm, tensioning belts to secure the load, large rubber supporting surface | universally applicable for passenger cars, particularly suitable for Mercedes-Benz automatic transmissions
Tool trays
Magnetic | 1 set / 2 pieces
Tool support
Ergonomic holder for impact wrench
Pad R
Support plate, rubber pad, round | load capacity 15 t, peg Ø 55 mm | 1 piece
Pads
Support plate, centering mushroom | for Fiat 500E, 500 ABARTH | 2-stage | 1 set / 4 pieces
Pads
Prism | for Mercedes G-Class – front and rear | 1 set / 4 pieces
Pads
Prism, mandrel | for Mercedes Sprinter, VW Crafter | 1 set / 6 pieces
Axial traverse ATH
1.5 t, peg Ø 35 mm, adjustment range 550 – 1200 mm, 1-fold telescopic | incl. 2 pads and 2 spacers
Axial traverse ATT 3,2
3.2 t, peg Ø 35 mm, adjustment range 630 – 1230 mm, 2-fold telescopic, incl. carrying plates | safe 2-point-support of vehicles such as Mercedes-Benz Sprinter, VW – LT 2
Axial traverse ATT 3.2 C
3.2 t, peg Ø 55 mm, adjustment range 868 – 1660 mm, 2-fold telescopic | for passenger cars and vans | incl. pad
Gearbox plate GA III
Adjustment angle +/- 40° / +/- 17°, load capacity 1 t, peg Ø 35 mm, measurements 400 x 300 mm (adjustable up to 600 x 400 mm), tensioning belt to secure the load
Gearbox plate GA IV
Adjustment angle +/- 12°, load capacity 1 t, peg Ø 35 mm, measurements 546 x 381 mm, in series galvanised, tensioning belts to secure the load, large rubber supporting surface
Pad X
Steel clamp | load capacity 20 t, peg Ø 55 mm | 1 piece
Pads
Prism | for VW MEB platform E-vehicles | 1 set / 4 piece
Pads
Support plate, U-support | 1 set / 4 pieces
Pads
Mandrel | for Fiat Ducato, Peugeot Boxer, Citroën Jumper – front and rear | 1 set / 4 pieces
Prismatic blocks
For GA IV | 2 pieces
Retrofit kit Parking position switch rolling jack
For scissor lift S38/S50
Spacer DS 2
30 t, peg Ø 55 mm, 150 mm | 1 piece
Axial traverse ATB NF
10 t, peg Ø 55 mm, adjustment range 420 – 1020 mm | suitable for low-level buses | incl. 2 sliders and 2 adjustable receptacle pins
Axial traverse ATEB S2
7.5/15 t, peg Ø 45/55 mm, adjustment range 200 – 620/830 – 1500 mm | special cross bar for secure seating of EvoBus buses, in particular the CITARO series | incl. 4 pads and 2 sliders
Axial traverse ATEB S2 TWIN
7.5/15 t, peg Ø 55 mm, adjustment range 200 – 620/830 – 1500 mm | special cross bar for secure seating of EvoBus buses, in particular the CITARO series | incl. 4 pads and 2 sliders
Bushing 55/35
Peg Ø 55 mm, standard peg Ø gearbox plates 35 mm | for BLITZlifts with mount Ø 55 mm | 1 piece
Bushing 55/45
Peg Ø 55 mm, standard peg Ø gearbox plates 45 mm | for BLITZlifts with mount Ø 55 mm | 1 piece
Bushing 80/35
Peg Ø 80 mm, standard peg Ø gearbox plates 35 mm | for BLITZlifts with mount Ø 80 mm | 1 piece
Bushing 80/45
Peg Ø 80 mm, standard peg Ø gearbox plates 45 mm | for BLITZlifts with mount Ø 80 mm | 1 piece
Connecting pieces ZS 100
1.5 t, 100 mm | 1 set / 2 pieces
Connecting pieces ZS 50
1.5 t, 50 mm | 1 set / 2 pieces
Fastening set ATT 3,2
10 t, peg Ø 35 mm | for secure placement of an axial traverse ATT 3,2 on the supporting bridge GS / GSB
Pad H
Wooden clamp | load capacity 20 t, peg Ø 55 mm | 1 piece
Pad P
Support plate, pin | load capacity 15 t, peg Ø 35 mm | special support for buses on frame (mushroom shaped support) | 1 piece
Pad R
Support plate, rubber pad, round | load capacity 15 t, peg Ø 35 mm | 1 piece
Pad U
Support plate, fork | load capacity 15 t, peg Ø 55 mm | 1 piece
Spacer DS 1
30 t, peg Ø 55 mm, 100 mm | 1 piece
Spacer DS 1
15 t, peg Ø 35 mm, 100 mm | 1 piece
Spacer DS 2
30 t, peg Ø 80 mm, 150 mm | 1 piece
Spacer DS 2
15 t, peg Ø 35 mm, 150 mm | 1 piece
Spacer DS 3
30 t, peg Ø 80 mm, 250 mm | 1 piece
Spacer DS 3
30 t, peg Ø 55 mm, 250 mm | 1 piece
Spacer DS 3
15 t, peg Ø 35 mm, 250 mm | 1 piece
Spacer tube DR 4
30 t, peg Ø 80 mm, 400 mm | 1 piece
Spacer tube DR 4
10 t, peg Ø 35 mm, 400 mm | 1 piece
Spacer tube DR 4
15 – 20 t, peg Ø 55 mm, 400 mm | 1 piece
Spacer tube DR 5
10 t, peg Ø 35 mm, 500 mm | 1 piece
Spacer tube DR 5
15 – 30 t, peg Ø 55 mm, 500 mm | 1 piece
Spacer tube DR 6
30 t, peg Ø 80 mm, 600 mm | 1 piece
Spacer tube DR 6
10 t, peg Ø 35 mm, 600 mm | 1 piece
Support platform
15 t, mobile | for use in conjunction with U-brackets, primed and lacquered, lowered under load
Supporting block DB
Wooden block, 100 x 200 x 360 mm, load capacity 15 t | for lowering the traverse onto the supporting bridge | 1 piece
Supporting bridge GS 15
15 t | Universal | to ensure that the vehicle is tilt-proof – pit lift can still be used | incl. roller set, 2 sliders, 2 spacer tubes, 2 pads, traverses and tool tray
Supporting bridge GSB
15 t | super flat, accessible for low-floor buses | incl. roller set, 2 sliders, 2 spacer tubes and 2 pads
Supporting bridge GSB Vario
15 t | super flat, accessible for low-floor buses | incl. roller set, 2 sliders, 2 spacer tubes and 2 pads
Supporting bridge GSV
15 t, adjustable 900 – 1180 mm | pit lift can still be used | incl. roller set, 2 sliders, 2 spacer tubes, 2 pads and tool tray
Supporting Package I
15 t, peg Ø 55 mm, movable | minimum equipment of a working pit | incl. supporting bridge GS, traverse ATS, 2 spacers and connecting set
Supporting Package II
15 t, peg Ø 55 mm, movable | basic equipment for lorry workshops with universal vehicle access | incl. 2 supporting bridges GS, 2 traverses (ATS, ATK), 2 spacers, connecting set and 2 spacer tubes
Supporting Package III
15 t, peg Ø 55 mm, movable | for bus and transport companies (low-floor buses) | incl. supporting bridge GSB, traverse ATB, 3 pads and 2 wooden blocks
Supporting Package IV
15 t, peg Ø 55 mm, movable | for repair shops with universal vehicle access – specialising in trucks, Unimogs, construction and specialised vehicles | incl. 3 traverses (ATK, ATS, ATB), 3 supporting bridges GS, 2 wooden blocks, 5 pads, 2 spacer tubes and 8 spacers
Traverse ATB
15 t, peg Ø 55 mm | standard traverse for buses, incl. 2 sliders and 4 pads
Traverse ATK
20 t, peg Ø 55 mm | front axle fork, incl. 2 pads
Traverse ATK
15 t, peg Ø 55 mm | front axle fork, incl. 2 pads
Traverse ATK
10 t, peg Ø 55 mm | front axle fork, incl. 2 pads
Traverse ATS 15
15 t, peg Ø 55 mm | standard traverse for trucks | incl. 2 sliders, 2 pads and 2 spacers
Traverse set ATB
15 t, peg Ø 55 mm | accessories for supporting trucks | incl. 2 sliders, 2 pads and 2 spacers
Traverse set ATB MAN TGA
15 t, peg Ø 55 mm | accessories for supporting MAN trucks at the axles | incl. connecting set, 4 pads and 4 spacers
Axial traverse ATEB
10 t, peg Ø 55 mm
Fastening set ATS
30 t, peg Ø 55 mm | for positioning a traverse safely on the supporting bridge GS